Certificate III in Engineering - Fabrication Trade

Code - MEM30319

This qualification defines the skills and knowledge required of an engineering tradesperson - fabrication within metal, engineering, manufacturing and associated industries. The qualification has been specifically developed to meet the needs of apprentices in the above trade. The qualification packaging has been developed on an assumption that competency will be developed through an integrated combination of on and off-the-job learning strategies such as those delivered through a formal apprenticeship. The qualification may also be achieved through formal skills recognition assessment processes.

The skills associated with this qualification are intended to apply to a wide range of fabrication work, including undertaking metal fabrication, structural steel erection, Sheetmetal work, welding, blacksmithing and surface finishing.

Assessment of some units of competency must, where indicated, include evidence of the candidate's performance in a functioning workplace where there is a sufficient range of appropriate tasks and materials to cover the scope of application of those units. All outcomes must reflect the standard of performance inherent in the job.

No licensing, legislative or certification requirements apply to this qualification at the time of publication. However, in some jurisdictions units in this qualification may relate to licensing or regulatory requirements. Local regulations should be checked

This qualification is designed to provide an industry recognised skills profile related to trade work as an Engineering Tradesperson – Fabrication. Skills development should be undertaken through an Australian Apprenticeship arrangement where the mix of on and off-the-job training would be specified in the Training Plan associated with the Contract of Training between the employer and apprentice.

• 18 years old and above at the time of enrolment
• Pre-training review
• LLN test

For Qualification by RPL the candidate MUST provide the following required documents:
1. 100 points ID
2. Unique Student Identifier – USI number
3. Resume (Relevant Industry)
4. Reference Letter (Relevant Industry)
5. Payslip
6. Work site Photos & Videos evidences

The students enrolled in MEM30319-Certificate III in Engineering – Fabrication Trade are required to complete 30 units of competency as listed below:

Core Units:

 

MEM09002

 

Interpret technical drawing

 

MEM11011

 

Undertake manual handling

 

MEM12023

 

Perform engineering measurements

 

MEM12024

 

Perform computations

 

MEM13015

 

Work safely and effectively in manufacturing and engineering

 

MEM14006

 

Plan work activities

 

MEM16006

 

Organise and communicate information

 

MEM16008

 

Interact with computing technology

 

MEM17003

 

Assist in the provision of on-the-job training

 

MEM18001

 

Use hand tools

 

MEM18002

 

Use power tools/hand held operations

 

MSMENV272

 

Participate in environmentally sustainable work practices

Elective Units:

 

MEM05004

 

Perform routine oxy fuel gas welding

 

MEM05005

 

Carry out mechanical cutting

 

MEM05007

 

Perform manual heating and thermal cutting

 

MEM05009

 

Perform automated thermal cutting

 

MEM05011

 

Assemble fabricated components

 

MEM05012

 

Perform routine manual metal arc welding

 

MEM05015

 

Weld using manual metal arc welding process

 

MEM05017

 

Weld using gas metal arc welding process

 

MEM05019

 

Weld using gas tungsten arc welding process

 

MEM05036

 

Repair, replace and/or modify fabrications

 

MEM05047

 

Weld using flux core arc welding process

 

MEM13002

 

Undertake work health and safety activities in the workplace

 

MEM05052

 

Apply safe welding practices

 

MEM05056

 

Perform routine flux core arc welding

 

MEM08010

 

Manually finish/polish materials

 

MEM10001

 

Erect structures

 

MEM12007

 

Mark off/out structural fabrications and shapes

 

MEM18055

 

Dismantle, replace and assemble engineering components

Assessment methods may include:
• Demonstration/Presentation/ On-Site observation
• Questioning / Written assessment task
• Research assignment / Project / Portfolio
• Role Play/Case Study

Not Applicable.

The processing period for the qualification is approximately 4 – 6 weeks time.

• Course fees (Classroom Blended): $
• RPL: $
• Enrolment Fees – $
• Certificate Re-issue Fees – $
• Administration Fees – N/A
• Material Fees – N/A

 

APPLY NOW